SDSS Strips and Super Duplex Perforated Sheet supplier in India

NORSOK Super Duplex Plate supplier in India offer wide selection of 25cr SS Coils and SDSS Shim Stock at very genuine price
A SDSS grade is designed with equal proportions of austenitic and ferritic composition. The Super Duplex Plate is a fixture that is designed in thickness above 6mm and extends up to 150mm. These plates possess superior strength and provide stability to different applications in the system. A Super Duplex Stainless Steel Plate is designed with a superior chemical composition consisting of chromium, nickel, and molybdenum alongside other constituting alloys. This content gives the plates good corrosion and oxidation resistance properties. The Super Duplex Steel Plate has enhanced mechanical properties and showcases good tolerance against pitting and crevice corrosion across stress-induced conditions. A Super Duplex Sheet is an aesthetically appealing grade that is not employed to provide stability, but on the contrary, adds a glow to the grade. These grades are usually designed in sizes above 0.5mm, but below 6mm.
The Super Duplex Foil is one of the thinnest metal grades designed in thicknesses of less than 0.2mm. These foils protect the grade against damage during storage and heat treatment procedures. SDSS Strips are slightly thicker than foils and are available in thickness between 0.2mm to 0.5mm. These strips act as filler metal during different welding procedures. The Super Duplex Shim Stock is used to fill space between machinery and other parts to provide stability and support. These components are designed in different shapes and sizes as per requirements. SDSS Coil is wound soon after it is rolled. These coils are a massive fixture that can be efficiently transported and later sheared into plates, sheets, foil, and strips. They are quality assured and produced with the best raw materials using cutting-edge technology.
Table of Content
Super Duplex Plate Specification
Material | Super Duplex |
Technique | Cold Rolled / Hot Rolled |
Standards | ASTM A240 / ASME SA240, AMS, MSRR, BS |
Available Length Range | 100 to 8000 mm (More than 8000 mm also) |
Available Width Range | 1000 to 2000 mm |
Hardness | Quarter Hard, Soft, Half Hard, Hard, Spring Hard etc. |
Temper | Annealed |
Condition | Polished on both sides |
Finish | Cold rolled sheet (CR), Hot rolled plate (HR), 2B, BA NO(8), 2D, SATIN (Met with Plastic Coated) |
Super Duplex Sheet Price List
Per Kg
H.R.PLATES GRADE SDSS WIDTH BELOW 600 MM
Per Kg
SDSS PLATES 20MM X2000MMX5500MM
Per Kg
SUPER DUPLEX SS PLATE (800X1500X10)
Per Kg
SUPER DUPLEX COLD ROLLED SHEET (200 WIDE X 0.2MM)
Per Kg
SDSS SHEET (0.500MMX1150MMX3000MM)
Per Kg
SDSS 32750 COIL 600MM X 0.4MM
Corrosion resistant Super Duplex Sheet stockist in Mumbai, superior strength and lowest price available in 8 mm, 10 mm, and 12 mm
Super Duplex Steel Plate Chemical Composition
Carbon (C) Max. | 0.030 |
Phosphorous (P) Max. | 0.035 |
Manganese (Mn) Max. | 1.20 |
Silicon (Si) Max. | 0.80 |
Iron (Fe) | Bal. |
Sulphur (S) Max. | 0.020 |
Nitrogen (N) | 0.24-0.32 |
Chromium (Cr) | 24.0-26.0 |
Nickel (Ni) | 6.0-8.0 |
Molybdenum (Mo) | 3.0-5.0 |
Other Elements | — |
Copper (Cu) | 0.50 |
SDSS Plate Mechanical Properties
Elongation A5(%) | Tensile Strength(MPa) | Proof Stress 0.2% (MPa) | Hardness Max (HB-HRB) |
15 | 795 | 550 | 310-32* |
Super Duplex Strip Equivalent Grade
AFNOR | UNS | Werkstoff NR. |
---|---|---|
Z3 CN 25.06 Az | S32750 | 1.4410 |
Physical Propertries of A240 SDSS Chequered Plate
Density | lb/in3 | 0.28 |
---|---|---|
Coefficient of Thermal Expansion 68-212°F/°F |
x10-6/°F | 7.2 |
Modulus of Elasticity | psi x 106 | 29 |
Heat Capacity | Btu/lb/°F | 0.12 |
Thermal Conductivity | Btu/h ft °F | 8.7 |
Electrical Resistivity | W-in x 10-6 | 31.5 |
Various Types of Super Duplex Plate
Super Duplex Plate
Super Duplex Sheet
Super Duplex Perforated Sheet
Super Duplex Stainless Steel Sheet
Super Duplex Steel Plate
Super Duplex Stainless Steel Plate
Super Duplex Plate Material
ASTM A240 SDSS Stainless Steel Sheet
Super Duplex Coil
Super Duplex Strip
SDSS 30 degree bevel plate
Hot Rolled Super Duplex Steel Plate
Cold Drawn ASTM A240 Super Duplex Plate
ASTM A240 SDSS Foil Sheet
ASTM A240 Super Duplex Mesh Plate
Super Duplex Chequered Plate
SDSS Polished Plate
Super Duplex Stainless Steel Clad Plate
Weight Of SDSS Plate
Nominal Size Thickness (inches) |
Weight (lb/ft2) |
---|---|
3/16 | 7.65 |
1/4 | 10.2 |
3/8 | 15.3 |
7/16 | 17.9 |
5/16 | 12.8 |
1/2 | 20.4 |
9/16 | 22.9 |
5/8 | 25.5 |
11/16 | 28.1 |
13/16 | 33.2 |
7/8 | 35.7 |
3/4 | 30.6 |
1 | 40.8 |
1 1/8 | 45.9 |
1 3/8 | 56.1 |
1 1/2 | 61.2 |
1 1/4 | 51.0 |
1 5/8 | 66.3 |
1 3/4 | 71.4 |
2 | 81.6 |
2 1/8 | 86.7 |
2 1/4 | 91.8 |
1 7/8 | 76.5 |
2 1/2 | 102 |
2 3/4 | 112 |
3 | 122 |
3 1/2 | 143 |
3 1/4 | 133 |
3 3/4 | 153 |
4 | 163 |
4 1/4 | 173 |
4 1/2 | 184 |
5 | 204 |
6 | 245 |
5 1/2 | 224 |
6 1/2 | 265 |
7 | 286 |
7 1/2 | 306 |
9 | 367 |
8 | 326 |
10 | 408 |
Distributor & supplier of Super Duplex Stainless Steel Plate as per ASTM A240 / SA 240 American Specification, check Super Duplex Coil price in India
Thickness of SDSS Polished Plate
Thickness (mm) | Dimensions |
---|---|
1.5 | 3m x 1.5m |
2.0 | 3m x 1.5m |
3.0 | 3m x 1.5m |
5.0 | 3m x 1.5m / 4m x 2m |
6.0 | 3m x 1.5m / 4m x 2m / 6m x 2m |
8.0 | 3m x 1.5m / 4m x 2m / 6m x 2m |
10.0 | 3m x 1.5m / 4m x 2m / 6m x 2m |
12.0 | 3m x 1.5m / 4m x 2m / 6m x 2m |
15.0 | 4m x 2m / 6m x 2m |
20.0 | 4m x 2m / 6m x 2m |
Low Temperature Impact Properties of SDSS Plate
Temperature °F | RT | -4 | 32 | -40 |
---|---|---|---|---|
Ft-lbs | 162 | 155 | 162 | 140 |
Temperature °F | -76 | -148 | -112 | -320 |
Ft-lbs | 110 | 30 | 44 | 7 |
ASTM A240 SDSS Plate Elevated Temperature Tensile Properties
Temperature °F | 392 | 68 | 302 | 212 | 482 |
---|---|---|---|---|---|
Ultimate Tensile Strength, ksi | 95 | 116 | 98 | 101 | 94 |
0.2% Offset Yield Strength, ksi | 58 | 80 | 61 | 65 | 55 |
Toughness Values of Hot Rolled Super Duplex Steel Plate
Temp. | -60°F | -50°C | +20°C | +70°F |
---|---|---|---|---|
Average (5) | 65 ft. lbs | 90 J/cm_ | 150 J/cm | 87 ft. lbs |
Single | 54 ft. lbs | 75 J/cm_ | 90 J/cm_ | 65 ft. lbs |
SDSS Plate Material Hardness
Average (5) | HV10 180-230 | HB : 180-230 | HRC _ 20 |
Dimensions of Super Duplex Plate
Metric Dimensions
Surface finish | Width (mm) | Thickness (mm) |
---|---|---|
2B – Cold rolled, heat treated, pickled, skin passed | max. 2032 | 0.25–8.0 |
2R – Cold rolled, bright annealed | max. 1524 | 0.25–3.5 |
2E – Cold rolled, heat treated, mechanically descaled | max. 2032 | 0.4–8.0 |
2D – Cold rolled, heat treated, pickled | max. 1524 | 0.4–6.35 |
2H – Work hardened | max. 1524 | 0.4–6.35 |
Polished, brushed | max. 1524 | 0.5–4.0 |
Imperial Dimensions
Surface finish | Width (in) | Gauge (in) |
---|---|---|
2B – Cold rolled, heat treated, pickled, skin passed | max. 72* | 10–24 |
Temper rolled Mexinox only | max. 48 | 13–29 |
BA Mexinox only | max. 48 | 18–28 |
2D – Cold rolled, heat treated, pickled | max. 60 | 12–24 |
Polished (not brushed) | max. 60 | 11–24 |
Urgent requirement of Super Duplex Steel Plate? Contact us for Non Standard sizes, Wide range of SDSS Chequered Plate, Clad Plate and Super Duplex Perforated Sheet in India
Geometry of Super Duplex Stainless Steel Coil

The internal diameter, external diameter, and width of the coil all influence its geometry. The interior diameter varies depending on the recoiler, however it usually falls into one of the following categories:
ASTM A240 Super Duplex Plate Tolerances
Gauge | LB/Sq In. | LB/Sq. Ft. | Gauge Tolerance | ||
---|---|---|---|---|---|
72″ Wide | 96″ Wide | ||||
3/16 | 0.1875 | 0.05958 | 8.579 | +.045″ -.010″ | +.050″ -.010″ |
7/32 | 0.2187 | 0.06854 | 9.870 | ||
1/4 | 0.2500 | 0.07750 | 11.162 | ||
5/16 | 0.3125 | 0.09546 | 13.746 | ||
3/8 | 0.3750 | 0.11456 | 16.496 | +.055″ -.010″ | +.060″ -.010″ |
7/16 | 0.4375 | 0.13250 | 19.080 | ||
1/2 | 0.5000 | 0.15044 | 21.633 | ||
9/16 | 0.5625 | 0.16838 | 24.247 | ||
5/8 | 0.6250 | 0.18633 | 26.831 | ||
11/16 | 0.6875 | 0.20427 | 29.415 | ||
3/4 | 0.7500 | 0.22308 | 32.123 | +.060″ -.010″ | +.065″ -.010″ |
13/16 | 0.8125 | 0.24102 | 34.707 | ||
7/8 | 0.8750 | 0.25897 | 37.291 | ||
15/16 | 0.9375 | 0.27691 | 39.875 | ||
1 | 1.0000 | 0.29628 | 42.665 | +.070″ -.010″ | +.075 -.010″ |
1-1/8 | 1.1250 | 0.33217 | 47.833 | ||
1-1/4 | 1.2500 | 0.36806 | 53.001 | ||
1-3/8 | 1.3750 | 0.40395 | 58.169 | ||
1-1/2 | 1.5000 | 0.43984 | 63.337 | ||
1-3/4 | 1.7500 | 0.51161 | 73.672 | ||
2 | 2.0000 | 0.58339 | 84.008 | +.125″ -.010″ | +.150″ -.010″ |
2-1/8 | 2.1250 | 0.62229 | 89.610 | ||
2-1/4 | 2.2500 | 0.65817 | 94.777 | ||
2-1/2 | 2.5000 | 0.72995 | 105.113 | ||
2-3/4 | 2.7500 | 0.80173 | 115.449 | ||
3 | 3.0000 | 0.87709 | 126.301 | +.150″ -.010″ | +.160″ -.010″ |
3-1/2 | 3.5000 | 1.02064 | 146.972 | ||
4 | 4.0000 | 1.16850 | 168.264 | +.180″ -.010″ | +.200″ -.010 |
Finishes of Super Duplex Stainless Steel Plate
Finish | Description |
---|---|
2B | Reflective grey shine with a smooth finish. The most common type of surface finish. |
Bright Annealed (BA) | Cold rolled and annealed in a controlled environment to keep a high-reflective finish. |
Dull Polish (DP) | Used extensively in the catering business, as well as push and kick plates, for ease of cleaning, brushed look, non-reflective.. |
Hot Rolled (HR) | Scaled finish, which is ideal if surface polish isn't a priority. |
ASTM A240 SDSS Sheet Advantages
Melting Point of Super Duplex SS Sheet
Melting Point | 2570 - 2660 °F (1410 - 1460 °C) |
Hot Rolled SDSS Plate Welding
Toughness Chart of Super Duplex Coil
Temp. | -50°C | -60°F | +20°C | +70°F |
---|---|---|---|---|
Average (5) | 90 J/cm_ | 65 ft. lbs | 150 J/cm | 87 ft. lbs |
Single | 75 J/cm_ | 54 ft. lbs | 90 J/cm_ | 65 ft. lbs |
Applications of Super Duplex Chequered Plate
A Supplier by choice of Super Duplex Plate in following projects


Weatherford Cielo - Abu Dhabi


Origin Energy Limited - Australia


Singapore Lng Corp - Singapore