Duplex Angle and UNS S31803/ S32205 Channel/ Beams supplier

Duplex 2205 Channel & UNS S31803 Beam supplier in India

Duplex Sections & Duplex Steel T Beams supplier in Mumbai

DSS is a high-strength stainless steel grade. A Duplex Channel is a device that is designed with one opening with the other three closed sides. These channels can be employed to provide stability and support to different applications. The Alloy 2205 Channel is designed with a chemical content of chromium, nickel, and molybdenum, allowing them good strength and long service life across different applications. The DSS Sections are designed with a hollow cylinder or in a square cross-section. These sections are generally welded in place. Duplex Sections are manufactured with a ferritic and austenitic microstructure. This gives them higher strength compared to standard austenitic grades. Duplex Beams are structural steel products that provide support to different heavy loads. These beams are designed to carry the vertical gravitational force but can also carry horizontal loads. The SAF 2205 T Beams is a load-bearing structure that reinforces different components. These beams act as compression members and help in resisting compressive stress in the system. The Duplex beam for bridge construction is very robust and can handle different pressures that are put on them. There may be more than one beam used for the construction the component from side to the other or across the top to act as a supporting deck. The Alloy 2205 Beams are versatile and cannot be attacked by termites or rodents, and provide structural integrity and safety to different applications. Stainless Steel 2205 Steel beams and Profiles can be rolled, drawn, and pressed in different shapes and in different cross-sections. The robust SAF 2205 Angle / Channel/ Beam is produced with the best raw materials and latest technology under the guidance of our renowned technicians.

A Duplex Angle is an L-shaped grade manufactured as steel is rolled in mills and produced in bending machines. The robust Alloy 2205 Angle is seen in brackets, trim, reinforcements, and framing of different angles of steel. The larger angle can handle good stress and weight. A UNS S31803 Angle is either hot or cold rolled depending on the requirements of the grade in different projects. The UNS S32205 Angle is designed with a superior chemical content allowing them to work well in aggressive conditions.

Duplex Steel Angles Types
2205 Stainless Steel Channel Dimension
DSS 2205 U Channel Sizes
SAF 2205 Bar Angle Channel Schedule
ASTM A479 S32205 Equal Angle Testing

Duplex Angle Specification

Standards	ASTM/ ASME A276/ SA276
Dimensions	DIN, AISI, EN, JIS, BS, ASTM, ASME
Grades	2205 (S31803 / S32205)
Angle	5 to 9mm
Flat	3″ thru 12.31″
Channel	300mm300mm~40mm20mm
Length	4MTR, 5MTR, 3MTR, 6MTR
Thickness	3.0 to 120mm
Type	C Channel, W Beam, Angle, U Channel, I Beam, H Beam, T Beam, Chain

UNS S32205 Channel Price List

15.35

Per KGS

115MM X 85MM X 355M ANGLES SHAPES AND SHAPES AND SECTION OFSS DSS 2205 HOLLOW BAR

4.56

Per KGS

Dia 50mm Alloy 2205 STAINLES STEEL, ANGLES, SHAPES AND BEAM OF S31803

63.96

Per KGS

LENGTH 85MM SAF 2205 MAIN SPOUT STOPPER CHANNEL GUIDE

Duplex Steel 2205 Beam Equivalent

UNS	WERKSTOFF NR.
S31803 / S32205	1.4462

Alloy 2205 Angles Chemical Composition

Grade	Fe	Mn	C	Si	S	P	Cr	Ni	Mo	N
S31803	63.72 min	2.00 max	0.030 max	1.00 max	0.020 max	0.030 max	22.0 – 23.0	4.50 – 6.50	3.0 – 3.5	0.14 – 0.20
S32205	63.54 min	2.00 max	0.030 max	1.00 max	0.020 max	0.030 max	21.0 – 23.0	4.50 – 6.50	2.50 - 3.50	0.8 – 0.20

Duplex SS Channels Mechanical Properties

Density (lb/in 3)	Density (g/cm 3)	Melting Point (°F)	Melting Point (°C)
0.285	7.805	2588 – 2669	1420 – 1465

Duplex Steel Angles Types

Duplex Steel 2205 Angle

Duplex Steel Unequal Leg Angle

Duplex Steel C Channel

Duplex Steel 2205 L Angle

ASME SA276 Duplex Steel I Beam

Duplex Anchor Chain

Duplex Architectural Angles

ASTM A276 Duplex Steel Angle

Duplex Steel H Beam

Duplex Equal Leg Angle

Duplex Steel 2205 Angle

Duplex Steel U Channel

Manufacturer & Supplier of Duplex Steel beams and Profiles, check UNS S32205 Angle weight chart & Price in India

2205 Stainless Steel Channel Dimension

Approx Weight (kilogram/meter)	Sizes	Approx Weight (kilogram/meter)	Angle Bar Sizes
1.13	25 x 25 x 3 milimeter	7.50	63 x 63 x 8 milimeter
1.46	25 x 25 x 4 milimeter	4.00	65 x 65 x 4 milimeter
1.78	25 x 25 x 5 milimeter	5.02	65 x 65x 5 milimeter
1.37	30 x 30 x 3 milimeter	7.75	65 x 65 x 8 milimeter
1.78	30 x 30 x 4 milimeter	5.35	70 x 70 x 5 milimeter
2.20	30 x 30 x 5 milimeter	6.40	70 x 70 x 6 milimeter
1.83	40 x 40 x 3 milimeter	6.85	75 x 75 x 6 milimeter
2.41	40 x 40 x 4 milimeter	9.05	75 x 75 x 8 milimeter
2.97	40 x 40 x 5 milimeter	7.35	80 x 80 x 6 milimeter
3.05	50 x 50 x 4 milimeter	9.65	80 x 80 x 8 milimeter
3.78	50 x 50 x 5 milimeter	11.98	80 x 80 x 10 milimeter
3.90	63 x 63 x 4 milimeter	12.20	100 x 100 x 8 milimeter
3.90	63 x 63 x 5 milimeter	18.00	100 x 100 x 12 milimeter

DSS 2205 U Channel Sizes

Est. Weight per Ft. Lbs.	Size in Inches	Est. Weight per 20' Bar
0.59	3/4 x 3/4 x 1/8	11.80
0.80	1 x 1 x 1/8	16.00
1.16	1 x 1 x 3/16	23.20
1.49	1 x 1 x 1/4	29.80
1.01	1-1/4 x 1-1/4 x 1/8	20.20
1.48	1-1/4 x 1-1/4 x 3/16	29.60
1.92	1-1/4 x 1-1/4 x 1/4	38.40
1.23	1-1/2 x 1-1/2 x 1/8	24.60
1.80	1-1/2 x 1-1/2 x 3/16	36.00
2.34	1-1/2 x 1-1/2 x 1/4	46.80
1.65	2 x 2 x 1/8	33.00
2.44	2 x 2 x 3/16	48.80
3.19	2 x 2 x 1/4	63.80
4.70	2 x 2 x 3/8	94.00
3.07	2-1/2 x 2-1/2 x 3/16	61.40
4.10	2-1/2 x 2-1/2 x 1/4	82.00
4.90	3 x 3 x 1/4	98.00
6.60	4 x 4 x 1/4	132.00
9.80	4 x 4 x 3/8	196.00

SAF 2205 Bar Angle Channel Schedule

MFG	FLANGE WIDTH IN IN.	WEB THICK. IN IN.	WEIGHT PER FT. IN LBS.
WEIGHT PER FT. IN LBS.	WEB THICK. IN IN.	DEPTH IN IN. X WT./FT./ LBS.	FLANGE WIDTH IN IN.	MFG
4.1	.170	C3 x 4.1	1.410	Hot Rolled
4.1	.170	C3 x 4.1	1.410	Hot Rolled
5.4	.184	C4 x 5.4	1.584	Hot Rolled
7.25	.321	C4 x 7.25	1.721	Hot Rolled
6.7	.190	C5 x 6.7	1.750	Hot Rolled
9.0	.325	C5 x 9.0	1.885	Hot Rolled
8.2	.200	C6 x 8.2	1.920	Hot Rolled
10.5	.314	C6 x 10.5	2.034	Hot Rolled
13	.437	C6 x 13	2.157	Laser Fused
11.5	.220	C8 x 11.5	2.260	Laser Fused
13.75	.330	C8 x 13.75	2.343	Laser Fused
18.75	.487	C8 x 18.75	2.527	Hot Rolled
15.3	.240	C10 x 15.3	2.600	Laser Fused
20	.379	C10 x 20	2.739	Laser Fused
25	.526	C10 x 25	2.886	Laser Fused
30	.673	C10 x 30	3.033	Laser Fused
20.7	.282	C12 x 20.7	2.942	Laser Fused
25	.387	C12 x 25	3.047	Laser Fused
30	.510	C12 x 30	3.170	Laser Fused
33.9	.400	C15 x 33.9	3.400	Laser Fused

Duplex 2205 Beams & Angle manufacturer in Mumbai, view our online Duplex Steel T Beams price list

ASTM A479 S32205 Equal Angle Testing

Hardness Test
Mechanical Testing
Positive Material Identification Testing
Chemical Analysis – Spectro Analysis
Micro and Macro Test
Flattening Test
Pitting Resistance Test
Intergranular Corrosion Test
Flaring Test

Manufacturer of Duplex Stainless Steel Hollow Sections in India, view our online prices

Alloy 2205 Angle Channel

Corossion Resistance

DSS 2205 corrosion resistance qualities are nearly identical to those of Alloy 316L due to its high chromium concentration of 23%.
SAF 2205 has better stress corrosion resistance qualities than 304L and 316L ordinary austenitic grades because to its DSS microstructure and low nickel and high chromium concentrations.
Alloy 316L is more resistant to pitting and crevice corrosion.
In chloride-containing aqueous solutions, outperforms Alloys 304L and 316L in stress corrosion cracking resistance.
It has a greater corrosion rate in boiling nitric acid (65%) than Alloy 316L.
Alloy 2205 performs well in abrasion/corrosion applications due to its high yield strength.

Structure

When compared to molybdenum-containing DSS, the microstructure of Alloy 2205 is relatively stable.
After annealing at a temperature of around, the microstructure contains almost equal proportions of ferritic and austenitic.

Weldability

TIG manual and automatic, PLASMA, MIG, SMAW, SAW, and FCAW can all be used to properly weld.
The Alloy 2205 microstructure makes the alloy less susceptible to heat cracking.
There is no need for pre-heating or post-welding.
The filler metal should be of the balanced ferrite/austenitic variety.

Mechinability